fecl2 nh4scn

Post time: 16-06-22

And high-quality data are constrained by production costs and production conditions, so some electric welding mesh manufacturers do not meet this requirement, in this case, there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.

Galvanized wire coating rough, passivation film is not bright, bath temperature is too high. If the cathode current density is too high, zinc content in the bath is too high or sodium hydroxide and DPE content is too low; Electroplating solution with solid particles or excessive foreign metal impurities, will lead to such problems. Solution: If the large roll galvanized wire to the above coating is rough, there may be solid particles in the plating solution. If the roughness of the part is severe, the current density may be too high.

Now it is more used in the binding of the construction industry. Compared with ordinary wire, it is also softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, saving a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. There are many kinds, which can be selected according to different uses. The device for making annealed wire is simple, and the utilization rate of the device is improved. The material properties of annealed wire can meet different processing needs.

2, galvanized silk mesh forming sheet storage ground should be flat, according to the symbolic needs of regular accumulation, height should not exceed 2M, and away from heat source, avoid exposure.

Usually according to the general people, the blade barbed rope is the guardrail, widely used in garden apartments, military bases, private residential areas, government machinery where there is a fence, generally used blade barbed rope. The biggest advantage of the blade is that the protective effect is good, and the installation and maintenance is very convenient, strong isolation ability, good resistance effect, etc.

Traditional barbed wire is crisscross woven into the wire, with the development of the economy, the rapid rise of all walks of life, the limitations of the use of traditional barbed wire gradually exposed, such as: aquaculture, to the chicken circle cage can not be too dense, the wire can not be too thick, woven mesh wire once the mesh will become soft. We also have coping methods: 1, cotton gouging, rolling straight wire into wavy shape, but still not enough to raise chickens with mesh can only be extended to the beak can not feed! 2, is the electric welding net, with the current of the longitude and weft wire spot welding together, the mesh is not limited to do more.

Galvanizing is a process of coating a metal surface with zinc in an electrochemical reaction on the metal surface to improve the corrosion resistance of the metal. Wire drawing is a process in which metal materials are drawn by mechanical methods to reduce their cross-sectional area and increase their length. So, the combination of galvanized to wire drawing two processes, what impact on the performance of the product?

Post time: 22-07-22

② Electric galvanized shaft wire direct selling shall not be used for waist hoop compression reinforcement, usually not used for all binding.

Copper sulfate point test is a simple way to quickly distinguish ordinary carbon steel and all types of stainless steel wire rope. The concentration of copper sulfate solution used is 5%-10%. Before the point test, the experimental area should be thoroughly removed from the oil or other impurities, and a small area should be polished by grinding machine or soft grinding cloth, and then the test liquid drops to the grinding place. Ordinary carbon steel or iron in a few seconds will form a layer of outer metal copper, and the surface of stainless steel does not produce copper precipitation or display copper color.

On the contrary, the denser the ion deposition, the better the quality of zinc layer. Under the condition that the surface zinc layer is dense and bright, the quality of zinc layer per unit area should reach 80g/m2, and the process parameters should be optimized as follows: current density is 16-20A /dm2, mass concentration of zinc sulfate solution is 500g/L, and pH value is 2.5-3.0.

Post time: 24-08-22

Hexagonal guardrail network custom structure is closely combined, the appearance is not concave and convex, with satisfactory corrosion resistance, oxygen resistance and other capabilities. Construction without a lot of manpower and material resources, can be operated on site.

During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.

Now it is more used in the binding of the construction industry. Compared with ordinary iron wire, it is softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, save a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. More kinds, can be selected according to different uses, making annealing wire device is simple, improve the utilization rate of the device. The material properties of annealed wire can meet different processing requirements.

The diameter of the wire is generally 0.3mm – 3mm, after the wire is not very strong, need to annealing, annealing this step is very important, can ensure the production of galvanized welding net, with good elasticity and toughness. After welding, the welding mesh becomes black wire welding mesh and can not be put on the market, because its corrosion resistance is poor and the service life is short, so it needs to be galvanized or dipped plastic treatment.

B. When the thickness of the plating is greater than 4 mm, the zinc adhesion should not be less than 610g/m, that is, the average thickness of the zinc layer should not be less than 86 microns.

Post time: 30-12-22

After proper heat treatment or cold drawing hardening, high carbon steel wire has high strength and hardness, high elastic limit and fatigue limit (especially notched fatigue limit), cutting function is acceptable, but welding function and cold plastic deformation ability is poor.

The production process of stainless steel blade and galvanized blade is basically similar. The blade size is usually determined according to the mold.

Materials of qualified quality should be kept marked for reference when used. In order to remove the surface film, surface inclusion and other defects on the surface of the large roll galvanized wire on the surface of the sedimentary layer to the local surface, it can be found and treated by conventional technology; Excess foam is caused by soaps and saponable fatty surfactants being brought into the tank. Moderate foam formation rates may be harmless. The presence of small homogeneous particles of large denier in the tank can stabilize the foam layer, but the accumulation of too many solid particles can cause explosion.

Post time: 08-06-22

4. Position of dog cage

Twisting hexagon mesh production factory is the selection of low carbon steel silk woven, mesh structure he has corrosion resistance, high strength and ductility and so on. The diameter of steel wire can reach 2.0mm-4.0mm. The surface of steel wire is usually used for hot-dip galvanized maintenance. The thickness of galvanized maintenance layer can be made according to the needs of customers.

185 compresores de aire diesel

martelo de perfuração

placa de triturador

fábrica de martillo submarino a alta presión

sand and gravel dredge pumps

vertically suspended centrifugal pump

la barra de perforación está hecha de los siguientes materiales

ql80 hammer

jaw crusher plate material