m pqq
Links
-
-
-
- The management system of the rinsing water after the steel wire pickling should be regularly and regularly discharged after the rinsing water, and the rinsing water should be kept clean and low acid value as far as possible. The pH control is more appropriate. The concentration of plating aid should not be too high. Hot plating wire must be added ammonium chloride and zinc chloride according to the data of laboratory analysis, and the specific gravity of the composite solution is controlled in the range of 50~80g/L. The addition of ammonium chloride or zinc chloride raw materials without the results of laboratory analysis shall be subject to criticism and education, and economic treatment if necessary.
-
- (3) For some use of special paint spraying should be baked, of course, depending on the size of the area, small can be placed in the oven, large can only be dried first, and then to dry parts for processing, lock baking, if other circumstances can only use high temperature tools bit by bit baking. The products that can be baked in the oven should be leveled at room temperature for 15 to 30 minutes, baked at a low temperature of 60 degrees Celsius for half an hour, and then baked at the reserved baking temperature for one and a half hours, and then cooled down.
- Welding net material has black wire, galvanized wire, wire drawing. Mesh has 1 inch, 2/1 inch, 3/1 inch, 4/1 inch, 4/3 inch, 8/5 inch, etc. Different materials, different mesh, used in different places. Therefore, welding net is an indispensable building material in construction industry.
- 4, barbed rope fence and culvert intersection, such as the ditch is narrow, barbed rope barbed rope fence can be directly across the ditch is wider, barbed rope barbed rope fence is difficult to cross, can take bridge, channel processing method.
-
Some customers do not understand the scope of application of different styles of barbed rope, there is a great difference.
-
Hot wire plating adopts zinc-free slag to add hot molten zinc and galvanizing, which avoids the traditional heating process, radiates 1653 hot molten zinc on surface 4102 of zinc liquid surface, and reduces the high temperature oxidation of zinc liquid surface. At the same time, the heating body is in contact with the zinc liquid, and the heat is directly transferred to the zinc liquid. The utilization rate of heat energy can reach more than 90%, and the heat radiation on the zinc liquid surface is reduced.
- Because the large roll galvanized wire alloy element in ore iron, can make copper through the thickness, hardness, impact force, strength, library rate, elongation, so alloy iron in the exercise of good iron, is an important auxiliary element. Galvanized wire and general wire is very different, general wire is cheap, and because the iron is not very stable, easy to rust in the wet place, so the stability is not very good, the life is not very long.
-
The price of galvanized iron wire performance is the key to win, galvanized wire only with good performance, in order to win the market, in order to obtain customer praise. In galvanized wire, the main function of carbon in increasing hardness, less is less easy to rust, the main function of chromium is acid and alkali resistance; Nickel’s main function is high temperature resistance, acid and alkali resistance and conductive use; The main function of iron is magnetic conductivity; The main functions of titanium are low density, high hardness and strong corrosion resistance. The main function of copper is magnetic and electrical conductivity. Different chemical components have different functions, which together form the characteristics of galvanized wire.
-
Post time: 15-07-22 - The cleaning agent used for cleaning has no effect on the adhesion of the coating and no corrosion on the base material. Acid activation Acid activation solution should be able to remove corrosion products and oxide film from the surface of parts without excessive corrosion of the matrix. Zinc plating may be zinc plated with zincate or chloride and appropriate additives shall be used to obtain a coating that meets the requirements of this standard. After light plating, light treatment is carried out. Passivated parts requiring hydrogen removal shall be passivated after hydrogen removal. Activation with 1% H2SO4 or 1% hydrochloric acid for 5 ~ 15s prior to passivation.
- Packing and binding galvanized wire is in the liquid state of zinc, after a messy physical and chemical effect, not only on the steel plated thick pure zinc layer, and also generate a zinc-iron alloy layer. This kind of plating method, not only has the corrosion characteristics of the electric galvanized wire, and because of a zinc alloy layer. It also has strong corrosion resistance that can not be compared with electric galvanizing. Therefore, this plating method is particularly suitable for a variety of strong acid, alkali fog and other strong corrosive environment.
- The most obvious difference in a short time is the cross section of this piece, hot dip galvanized barbed wire because of surface anticorrosion treatment, so there will be rust in the cross section of this piece, and stainless steel barbed wire because the internal raw materials and surface raw materials are consistent, so there is no such situation.
-
Post time: 31-08-22 - Selection of cage size tips
-
-
Post time: 12-06-24 -
-
A pet carrier can be used as an indoor or outdoor pet house. The dog cage is equipped with a fixed food basin and water fountain, and the foot plate pet cage rubber pad has bayonets on four sides to be splintered. It can be spliced, cut and disassembled according to the size of the cage. It is convenient and easy to clean. It can solve the problem of pinching the feet of the puppies in the ordinary cage and prevent the puppies from causing adverse reactions in the development. The dividers are breathable and comfortable, and can be used as heat shields for pets in summer. A puppy with small feet, no feet, no pinching.
- 2.25*2.25mm indicates that the two strands are 2.25mm silk, and the thorn thread is also 2.25mm silk;
- Two, cold galvanized wire production process of galvanized. Galvanizing is the core process in the production of cold galvanized wire, mainly by soaking the steel wire in a molten zinc solution to form a zinc layer on its surface.
-
With the improvement of people’s living standards, now many families are raising some small pets, these small pets also need a safe nest, pet cage has become an important choice of people, each pet’s habits and living habits will choose to adapt to the cage.
-
Post time: 15-05-23 -
Now when most people buy barbed rope, they choose blade barbed rope. Why is this? From the material, the blade barbed wire process is made of hot-dip galvanized steel plate or stainless steel sheet to press the sharp blade sheet, and the high-tension galvanized steel wire or the blade barbed wire is made of stainless steel wire as the core wire. Because the shape of the gill net is not easy to contact, so it can reach an excellent protective barrier effect.
-
- The basic requirements are the flatness of the net surface, hook mesh first after weaving, weaving process, rolling flowers can not turn, to adhere to smooth, can not present wire or turn flowers.
- The material of the electric welding net is black wire, galvanized wire and wire drawing. The mesh is 1 inch, 2/1 inch, 3/1 inch, 4/1 inch, 4/3 inch, 8/5 inch, etc. Different materials, different mesh, used in different places. Therefore, electric welding net is an indispensable building material in the construction industry.
-
Large hexagonal net is called stone cage net, mainly used for mountain protection, hydraulic construction, etc. Small wire hexagonal net is used as a good breeding material, the twisted flower hexagonal net in the welding of the iron frame get on the hexagonal net burning welding coops, pigeonholes, rabbit cages and other cage, hexagonal net is the best breeding material with the net.
-
During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.
-
-
- 185 compresores de aire diesel
- martelo de perfuração
- placa de triturador
- fábrica de martillo submarino a alta presión
- sand and gravel dredge pumps
- vertically suspended centrifugal pump
- la barra de perforación está hecha de los siguientes materiales
- ql80 hammer
- jaw crusher plate material
- panneau latéral de broyeur de titane